Packing

Available in four standard Non- Asbestos grades to suit a variety of applications, the sealants can be used to replace conventional compression packing in centrifugal pumps, valves and other rotating equipment where compression are being used.

Thermo-Pak™? TP002
A blend of synthetic fibers and non-staining lubricants for General services & Pulp & Paper Mills, Slurries, Sewage.
Color : Cream
Linear Speed : 2350FPM
pH Range : 2 to 12
Max. Temp.: 500 ^oF (260^oC)

Thermo-Pak™? TP0048
A blend of high performance fibers and chemically resistant lubricants. General services, Waste Water, Sewage, Sea Water, Slurries, Pulp & Paper, Mills, Brine and Hot Oil.
Color : Black
Linear Speed : 2350FPM
pH Range : 0 too 14
Max. Temp.: 50 ^oF(260^oC)8

Thermo-Pak™? TP005
A non-staining, non-toxic fiber blended with FDA approved lubricants for clean or food grade applications, Slurries, Potable Water, Pulp & Paper.
Color : Pure While
Linear Speed : 2350FPM
pH Range : 0 to 14
Max. Temp.: 500 ^oF (260^oC)

Thermo-Pak™? TP2000
A blend of exfoliated graphite particles and high temperature sacrificial lubricants for extreme service applications. Boiler Feed Pumps, Hot Oil.
Color : Black
Linear Speed : 4000FPM
pH Range : 0 to 14
Max. Temp.: 1112 ^oF (600^oC)68

Thermo-Pak™? Seal Cage Kit Sizes in Brass Spacer Pins8

Thermo-Pak™? Seal Cage Kit Sizes in Delrin Spacer Pins are available for Part No. TPC-438 , TPC-500 , TPC-563 , TPC-625 and TPC-750.

An Easy and Convenient Product to Use
Thermo-Pak™? injectable sealant are easy to install. The initial installation of packing and Thermo-Pak ™? Seal Cage materials are done by hand. Tightening the gland nut compresses the Thermo-Pak™? material and forces it to conform to any irregular spaces caused by wear.
An anti-extrusion ring composed of suitably sized braided packing material is set at the top and bottom of the stuffing box or packing gland to prevent the Thermo-Pak™? sealant from beign forced out when pressure is applied.

Thermo-Pak™? Injection Gun
Thermo-Pak™? injection gun utilizes a button-head or flow-through fitting which is permanently installed on the pump or valve stuffing box.

Since it requires no electricity, Thermo-Pak™? injection gun can be used anywhere to replenish sealant easily and conveniently.

The all-steel hydraulic gun is completely portable and is very easy to use. The valve or pump stuffing box fitting allows Thermo-Pak™? sealant to be hand-injected into the shaft stuffing box using the injection gun. No downtime is required for the re-packing operation since the equipment can continue to run during the re-packing operation.

How to Use Thermo-Pak™? Injection Gun

To properly replenish the packing material, the stuffing box fitting must be located. Next, the injection gun is coupled to the fitting. When the gun is properly coupled to the fitting, the on-off handle on the fitting is turned to the open position and the new Thermo-Pak™? sealant is pumped into the fitting until the required amount of sealant is injected. When the operation is complete, the fitting handle is placed in the off position and the injection gun is disconnected from the stuffing box fitting. Remember to properly

disassemble and return your injection gun to its container where it may be stored until needed again. Note: Button-head fittings with check ball valve do not require ball valve for on-line re-packing.

Gasket

Engineering Plastic

Hydraulic Seals

Special Products 1

Special Products 2

Valves